infra:lights
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
| infra:lights [2025/02/14 18:36] – created 404d | infra:lights [2025/04/01 20:56] (current) – [Artnet] 404d | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Lighting @ Humla ====== | ||
| + | |||
| + | |||
| ===== General ===== | ===== General ===== | ||
| ===== Mate-light ===== | ===== Mate-light ===== | ||
| + | |||
| + | ==== About ==== | ||
| + | {{ : | ||
| + | |||
| + | The matelight has two sets of connection: | ||
| + | |||
| + | * The data lines are sequential - everything' | ||
| + | * The power lines are connected wherever, but it's easiest to keep them at the bottom | ||
| + | |||
| + | Each box has a sequential string of lights which runs in a serpentine pattern. When seen from behind, data in should be on the lower left, and data out at the upper left. | ||
| + | |||
| + | It's held together by two ratchet straps which are joined together with the ratchets on the same side. | ||
| + | |||
| + | {{: | ||
| + | |||
| + | Fig A: a Ratchet | ||
| + | |||
| + | ==== Teardown ==== | ||
| + | |||
| + | {{ : | ||
| + | |||
| + | 0. Disconnect the power | ||
| + | 1. Disconnect the short data lines (pink circles) | ||
| + | 2. Disconnect the long data lines and take the cables out (green) | ||
| + | 3. Disconnect the micro controller and take it out (orange) | ||
| + | 4. Release the WAGO clamps with the power. You can keep one end connected | ||
| + | 4. Open the ratchet strap | ||
| + | 5. Take table off and take boxes off | ||
| + | 6. Stack as regular mate crates, bring extra snacks along on the side | ||
| + | | ||
| + | ==== Setup ==== | ||
| + | |||
| + | 1. Put ratchet strap out on the floor (the part without the ratchet). The hook should be on the right when you're looking at (what will become) the back of the device. | ||
| + | 2. Put the crates on the strap, with the corner of the rightmost crate about 30 cm from the hook | ||
| + | - Start and end of LED chain should be on the left side of the crates | ||
| + | - The crates marked with green duct tape (middle of short sides) should be at the bottom (have been set up with power connectors) | ||
| + | - The one crate with pink duct tape (middle of short sides) HAS to be at the top left (it doesn' | ||
| + | 3. Put table in place, edge to edge on the front | ||
| + | 4. Connect the ratchet strap hooks (long strap to long strap) on the right | ||
| + | 5. Connect the hooks of the ratchets on the left | ||
| + | 6. Thread the straps through each ratchet, and pull through until 5 cm before they get tight | ||
| + | 7. Fasten both ratchets so that the straps are fairly tight, and ratchets are aligned around the middle. Hide overflow strap somewhere so that nobody stumbles in them. | ||
| + | 8. Connect data (reverse of teardown 1-3) | ||
| + | 9. Connect power (reverse of teardown 4) | ||
| + | - Connect the matelight data line to the output from the microcontroller which does _not_ have black tape on it (that' | ||
| + | 10. Connect to power and it should Just Work™ | ||
| + | | ||
| + | ==== moar pix ==== | ||
| + | |||
| + | {{: | ||
| + | {{: | ||
| + | {{: | ||
| + | {{: | ||
| + | {{: | ||
| + | {{: | ||
| + | |||
| + | ---- | ||
| ===== DMX ===== | ===== DMX ===== | ||
| ^ Start ^ Channels ^ Location ^ Fixture Type ^ | ^ Start ^ Channels ^ Location ^ Fixture Type ^ | ||
| - | | 10 | 4 | Tak, mot lydrack | + | | 10 | 6 | Ceiling, towards audio rack | [[https:// |
| - | | 20 | 4 | Hylle, mot prosjektbord | + | | 20 | 6 | Shelf, towards project shelf | [[https:// |
| - | | 30 | 4 | Tak, mot Mate-light | + | | 30 | 6 | Ceiling, towards fridge/ |
| - | | 40 | 4 | Hylle, mot pinball-sofa | [[https:// | + | | 40 | 6 | Shelf, towards |
| - | | 50 | 4 | Tak, mot Mate-lager | + | | 50 | 6 | Ceiling, towards the stock of Mate boxes | [[https:// |
| - | | 60 | 4 | Tak, mot laptopbord | + | | 60 | 6 | Ceiling, towards laptop table | [[https:// |
| + | |||
| + | ==== Artnet ==== | ||
| + | ^ Node ^ Universe ^ Description ^ | ||
| + | | 10.10.3.21 | 9 | WLED - Prusa | | ||
| + | | 10.10.3.22 | 10 | WLED - Sprinkler | | ||
| + | | 10.10.3.24 | 3-4 | WLED - Matelight (Multi RGB + Dimmer) | | ||
| + | | 10.10.3.25 | 2 | WLED - PAR (Effect + Dimmer) | | ||
| + | |||
/srv/hackeriet-wiki/dokuwiki/data/attic/infra/lights.1739558205.txt.gz · Last modified: 2025/02/14 18:36 by 404d